Home > Default > USB-6009 labview 7.1

USB-6009 labview 7.1

October 11Hits:0
Advertisement
Hi can anybody tell me if they have had any problems running USB-6009 with Labview version 7.0? I can't get it to recongnise my device and it's behaving as if there is nothing there. Do I need version 7.1 or is there a more sinister problem afoot?
Kyle

Answers

What version of DAQmx Base are you using? The latest version, 1.4, is supported on all versions of LabView 7.0 and higher. It can be obtained using the following link:
http://digital.ni.com/softlib.nsf/websearch/941677622E793A2686256F8C0083641A?opendocument&node=132050_US

Read other 2 answers

Tags:

Related Articles

  • USB-6009 labview 7.1October 11

    Hi can anybody tell me if they have had any problems running USB-6009 with Labview version 7.0? I can't get it to recongnise my device and it's behaving as if there is nothing there. Do I need version 7.1 or is there a more sinister problem afoot? Ky

  • USB-6009 with Labview 2014 on Windows 8.1October 11

    Hi, I have trouble connecting USB-6009 OEM with my new laptop with windows 8.1. My USB-6009 OEM device is not shown up in NI Max. So when I check Device Manager, there is a question mark on "NI USB-6009 OEM FW". I tried to install Labview 2011 b

  • USB-6009 Sine WaveOctober 11

    Hi, I am new to LabView and am having some trouble. I need to input two sine waves into a USB-6009. I have a voltmeter that should read the output. Two of the problems that I have had thus far: I can only use "On Demand" in DAQ Assistant and eve

  • Usb 6009 continuous analog outputOctober 11

    Hi I'm pretty new to Labview, so you may have to bear with me. I have a USB-6009 and I want to generate a continuos analog output voltage. I've got the example you have posted 'Gen Mult Volt Updates-SW Timed_LV7.1 (0 to 4).vi' working and it outputs

  • Usb-6009 high-speed continuous acquisition for slow control loop applicationOctober 11

    Hi, After watching a few Youtube videos, I successfully built a control loop in LabVIEW using my USB-6009. Currently, this loop is limited by the speed my actuator can take and respond to commands, topping out at 200 Hz. This is completely sufficient

  • USB-6009October 11

    I am electrical engineering student and i design a project which the sensor signals through USB-6009 to PC labview for monitoring, but i dont know this sensor and USB-6009 can do this function or not? anyone can help, Thank you! Attachments: FFP350_p

  • USB 6009 Python ControlOctober 11

     Hello,  I am attempting to use python (with ctypes) to control my USB-6009.  The goal is to write out an analog voltage and then read in the voltage through an analog input with ability to change the number of points averaged and the number of times

  • USB 6009 thermocouple noiseOctober 11

    I'm using NI-DAQmx 7.5, Labview 7.0, and a USB-6009. I'm trying to get a more accurate reading from my j-type thermocouple.  It is now distorted with noise and jumps rapidly +/- 20 degrees around room temp without any heat being applied.  When heat i

  • USB-6009 DAQOctober 11

    Hi; Would you please advise which NI-DAQ software version is for USB-6009 using LabVIEW 7.1? RegardsHi; I have downloaded NI DAQ MX 8.9 which is supports LabVIEW 7.1, but it can not detect the NI USB-6009 driver and still asking for the driver. Can a

  • USB-6009 digital input change detectionOctober 11

    Hi,   I am trying to acquire digital signals from an ni usb-6009 device using daqmx on labview 8.0. I need to write the signals from a port of the device to an output file only when there is a change in the signals and I am not able to do this succes

Copyright (C) 2019 wisumpire.com, All Rights Reserved. webmaster#wisumpire.com 14 q. 0.442 s.