Home >

dot11 syslog command

Advertisement
  • Dot11 syslog command in IOS version 15.2(4)M5November 30

    Dear all, can you please advise what the equivalent command is for "dot11 syslog" on Cisco IOS Version 15.2(4)M5 because the router is not taking it? We are trying to execute it on a 1900 series Cisco router. Previously IOS 12.4(15)T6 on a Cisco

  • About the output of "show dot11 associations" command.November 30

    Hello. I have been made to the research of IP Phone 9971 . (Used by Wireless) The schematic diagram is shown below.   CUCM       |   L3-SW       |   AP 1142 (FW:15.2(2)JB)       |   CP-9971 (FW:9.3(2)) The results of the "show dot11 associations"

  • Syslog command for Clients associationsNovember 30

    Hello. For WLC 5508 software version 7.0.235.0, Does anyone know which command is needed to get the WLC send syslog messages everytime a wireless client associate and desassociate? Greettings.I believe of you set your staking level to debug or inform

  • Need help with IOS commands to see wireless printerNovember 30

    Seems that I'm not asking the question correctly, or providing the right information. The problem: I've purchased a wireless printer, (an HP 6500a) and I can not see / ping / use the printer on the wireless network. Environment: Cisco 891 ISR in stan

  • %DOT11-7-AUTH_FAILED: %DOT11-6-DISASSOC:November 30

    Hello again, Thought this issue was fixed yesterday after finding out my printer was the MAC address flashing up on the log, however it seems that every device is playing up. Thanks James These are my wirless devices,  APPLE IPHONE     6809.2780.219a

  • %DOT11-7-AUTH_FAILEDNovember 30

    Hello, I have problem med wireless authentication. Have tried following Operative system on clients. Windows XP, Windows Vista and Windows 7. Radius Server is working normally. Under here is debug, version and configuration. Kan somebody se something

  • EEM syslog issueNovember 30

    I have an issue with the syslog output of my eem script. The syslog command below does work. It sends an individual syslog message to my mgmt station for EACH line of cli output. I confirmed this with wireshark. The "show log" output looks fine

  • Cisco1941W error massage "%DOT11-7-AUTH_FAILED: Station 0011.f596.eecb Authentication failed"November 30

    I am using Cisco1941W. When I connect CliantPC to Wireless(1941W) I got bellow massage from 1941AP. "%DOT11-7-AUTH_FAILED: Station 0011.f596.eecb Authentication failed" And I couldn't ping from my PC to AP and Router. Its possible communication

  • Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELPOctober 11

    Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901. I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles.  Phone downloaded SEP...xml file from CME,after that phone

  • How to change CUE ip address?October 11

    Hi, We moved to a new location and using comcast as ISP. I was setting up the phone system today and met a few problems. 1. First of all, all the phones are connected and working(total of 4), but I can only see 3 of them showing up in the CCA. Whats

  • Trouble with my T1's and E1's in the lab - please help.... :-)October 11

    I'm working through my CCIE Voice/Collaboration training materials and am just about finished with the physical construction of the lab.  At this time I'm just going to install a new T1 card into my BR1 router and I'm trying to get my T1 to HQ (HQ ro

  • Access from Inside to Outside ASA 5510 ver 9.1October 11

    Hi All, I need some help in getting an ASA up and processing traffic from the inside network to the internet. I have a Cisco 2811 Router behind a Cisco ASA 5510. From the ASA I can ping the 2811 and I can ping IP addresses on the internet. I have upd

  • IOS SSL VPN WITH RADIUS AuthorizationOctober 11

    Hi I'm trying to authenitcate and authorize  the users loggining into SSLVPN via ACS and although the ACS loggs and "TEST" command on the router shw succeeful authentication i receive the flollowing debug *Jun  6 22:39:50.157: %SSLVPN-5-SSL_TLS_

  • QoS / Native VLAN Issue - Please HELP! :)October 11

    I've purchased 10 Cisco Aironet 2600 AP’s (AIR-SAP2602I-E-K9 standalone rather than controller based).  I’ve configured the WAP’s (or the first WAP I’m going to configure and then pull the configuration from and push to the others) with 2 SSID’s. One

  • Site-to-site VPN with remote accessOctober 11

    Hello friends, Company has a few remote offices and goal is connect all in yhe VPN. I have one IPSec VPN tunnel between remote1 and central office. Tunnel status is active and everything is ok. Other remote offices access to central server over remot

  • Site to Site VPN between ASA 5505 and Cisco 800 routerOctober 11

    Evening all, Hoping that someboy can see the error of my ways.  It seems very like the problem that i read here: https://supportforums.cisco.com/thread/2016300 We have a cisco 800 in a remote site which we wanted to use for a site to site vpn.  Went

  • WLAN Clients not browsing on Cisco Wireless Controller WLC NME-AIR-WLC12-K9October 11

    HiI have a question and i need a solution and expert help.I have done a deployment which involves Security (ASA5540), Routing/voice gateway/wlc NME-AIR-WLC12-k9) and Switching (Cisco3845-ccme/k9)Below is the list of equipment used:1. Cisco ASA 5540 -

  • Need help setting up static NAT to internal serverOctober 11

    One of my internal servers requires it to be available to the internet I am having a hard time allowing it to be NATed through my Ciscc 2801 router. It seems as though im missing something small. From what I can gather it seems as though its as issue

  • Cisco 7941 Not Registering in CME 8.6October 11

    Hi I would appreciate if somebody could really help me with this. The status-> Firmware version list on my phone is as below: Load File: *term41.default* App Load ID:jar41sccp.9-3-1ES13.sbn JVM Load ID:cvm41sccp.9-3-1ES13.sbn OS Load ID:cnu41.9-3-1ES

  • CME 8.6 IssueOctober 11

    ! Last configuration change at 16:28:19 GMT Mon Feb 27 2012 by admin version 15.1 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption hostname CCME2811 boot-start-marker boot-end-marker logging b

Copyright (C) 2019 wisumpire.com, All Rights Reserved. webmaster#wisumpire.com 11 q. 1.195 s.